Who This Checklist Is For

If you're the person stuck between a manufacturing line start date and a purchase order that isn't signed yet, this is for you. Nine steps, roughly in the order you should do them. I'm not a machine builder — I work on the sourcing side, coordinating rush orders for pharmaceutical, food, and cosmetics manufacturers. Over the past five years I've handled 130+ urgent cartoning machine and packaging line purchases, and the ones that went sideways almost always skipped one of the steps below.

This isn't a marketing piece. Each step comes from something I watched go wrong, or something that once saved us two weeks. Skip any one of them and you'll probably find out in the factory acceptance test — which is the worst place to find anything.

Here's what actually works.

Step 1 — Lock the Carton Style Before You Contact Anyone

Before you filter suppliers, before you write the spec, decide the format. This is the single most expensive decision in the whole order, and getting it wrong resets everything downstream.

  • Horizontal cartoning machine — the carton lies flat and the product is loaded from the side. Good for blister packs, small bottles, tubes, sachets.
  • End load cartoning machine — product enters from the end of the carton. Suited to bottles, vials, tubes, medical devices, and anything handled upright.
  • Automatic cartoning machine — this describes the drive system, not the format. It's not a spec on its own.

I've watched a pharmaceutical client lose three weeks right here. They sent an RFQ for an "automatic cartoning machine" when what they actually needed was a horizontal unit for blister packs. Suppliers quoted end load units back, the client got confused by inconsistent specs, and by the time we untangled it the original delivery window was gone. When I first started sourcing, I assumed suppliers would just tell buyers they'd asked the wrong question. They usually won't — they quote what was requested.

Step 2 — Write Your Compliance Requirements Before the First Email

Determine which certifications and documents apply to your facility before you look at a single quote. If you're supplying the U.S. pharmaceutical market, 21 CFR Part 11 governs electronic records and signatures, and it affects how the machine controls are documented. In the EU, the Machinery Directive (2006/42/EC) sets the baseline for CE marking. If the machine enters a medical-device cleanroom, ISO 13485 may also apply.

Per the EU Machinery Directive (2006/42/EC) and the U.S. FDA's 21 CFR Part 11, machine documentation requirements vary by market. Confirm which requirements apply to your facility before issuing your RFQ — as of 2025, requirements are unchanged, but always verify the current version at the official source.

One thing buyers miss constantly: most "CE certificates" on cartoning machines are self-declarations. That's legal — a lot of industrial machinery qualifies for the self-certification route — but it carries different weight than a Notified Body certificate. Ask specifically what type you're being given, for that machine, in writing. "We have CE" doesn't answer the question.

Step 3 — Filter Manufacturers by Real Format Experience, Not Catalog Breadth

Cartoning machine manufacturers publish long lists of models. But a supplier who's strong on horizontal cartoners isn't automatically strong on end load. Two questions will separate them fast:

  1. How many units matching my product format did you ship last year?
  2. Can you send me a video of that exact model running at a customer's site?

If they can't give a specific number, drop them. A supplier without reference installs in your format is asking you to be the beta test.

Step 4 — Ask for a Production Video, Not a Showroom Demo

A demo cell at a trade show and a client's factory floor are different worlds. You want footage of the machine running in a real line, with the client's actual cartons, at the client's actual line speed. Unedited. With the changeover sequence shown. If they have a clip of clearing a jam, even better.

Rendered animations look great. They also tell you nothing. If the only thing a supplier can send is a 3D walkaround, that's a data point in itself.

Step 5 — Get a Quote With a Line-Item Spare Parts List

A real quote covers more than the base unit. It includes tooling, the spare parts kit, common wear items, electrical drawings, PLC model and programming software, and warranty terms. All line-itemized.

Here's where the value-over-price argument gets concrete. A client of ours once received a quote 18% below the next bidder. On paper that looked decisive. Then we priced the spare parts list. The low bid had sensors and gripper heads priced two to three times higher than the other suppliers, and needed replacement more often. Over three years of ownership, the extra spares cost more than the sticker-price saving, and put a stop on the line when a part had to be air-freighted in. That's not a deal. That's a deferred bill.

I can only speak to how this plays out in the pharma and food segments — if your production runs are short-batch and changeover-heavy, the spare parts math gets even more lopsided. Standardize your comparison around three-year cost, not unit price.

Step 6 — Ask What the Changeover Time Is, and Make Them Prove It

Changeover time is the parameter new buyers skip most often. If you run multiple carton formats on one line — 10ml vials today, 2ml vials tomorrow, 30-count to 60-count next week — changeover time is throughput.

A machine that changes over in 25 minutes and one that takes 90 minutes look identical in a brochure. One runs three shifts of mixed production; the other runs one format per shift and a lot of waiting. During the factory acceptance test, ask the supplier to do a full changeover with your carton spec, timed, in front of you. Whatever number they've written on the datasheet, the hands-on number is the real one.

Step 7 — Confirm the After-Sales and Spare Parts Channel in Writing

Ask these questions and get written answers:

  • Where do spare parts ship from, and by what logistics route?
  • How long is the typical spare parts lead time to our region?
  • Who handles customs clearance on spare parts, and on what terms?
  • Is service handled by a local partner, or does an engineer need to fly in?
  • What's the typical response time for a downtime call?

"We support you anytime" is not an answer. For critical sensors and drives, most buyers I work with keep a small local shelf stock, because air freight is three to seven days at best — long enough to stop a line for a full week.

Step 8 — Put Your FAT Date in the Purchase Order

The factory acceptance test isn't a courtesy visit. It's a date, a document, and a set of signatures. Your PO should specify the FAT date, the acceptance criteria (speed, reject rate, changeover time, noise, documentation package), and what happens if items fail.

When something fails — and if you're honest with your spec, small things usually do — the punch list from the FAT becomes your strongest negotiating lever. Push for resolution before shipment, not after arrival. Fixing it in the supplier's factory is cheap. Fixing it in yours means customs, travel, and downtime.

Step 9 — Calculate Full Landed Cost, Not FOB Price

The last step and the one that usually decides whether the project was actually cheap. Landed cost includes: unit price + spare parts package + installation and commissioning + engineer travel + training + projected three-year spare parts + duties and customs + internal validation cost (if you're GMP-regulated).

When I compared our top-three vendors across full landed cost for a recent client, the lowest FOB quote landed in the middle of the pack. The spreadsheet said pick one vendor; the numbers on total cost said another. Went with the numbers. Two quarters later, when a sealing jaw needed replacing, the cheaper-up-front vendor's part was a two-week air shipment. The other one had it next day from a regional warehouse.

The difference in FOB price was around 11%. The difference in cost of downtime was a number I won't put in print.

Common Mistakes Buyers Make

  • Comparing unit prices. Nine times out of ten, it's the wrong comparison. Compare landed, three-year cost.
  • Not specifying format. "Automatic cartoning machine" is not a spec. Horizontal or end load — pick one before you email anyone.
  • Assuming CE is CE. Self-declaration and Notified Body certificates aren't equivalent in practice. Ask which one you're getting, for which machine.
  • Forgetting spare parts in the budget. A machine that costs $12k in spares over three years was never really $12k cheaper than the one that didn't.
  • No buffer in the timeline. Roughly half the emergency sourcing calls I get could've been avoided with a two-week buffer. Build it in even if the schedule looks comfortable.

None of these are exotic. They're the things that keep coming back. In the rush orders I handled last year, fewer than one in five buyers had worked through all nine steps before signing. The other four ended up calling someone like me to clean up after them.

If you're about to issue an RFQ for a cartoning machine — pharmaceutical, horizontal, end load, whatever the configuration — run this list with someone who isn't selling you anything. Two hours of careful answers usually saves two to three weeks of scrambling.